11
Gi1/46, Gi2/8 Gi2/9, Gi2/10, Gi2/11, Gi2/12, Gi2/13 Gi2/14, Gi2/15, Gi2/16, Gi2/17, Gi2/18 Gi2/19, Gi2/20, Gi2/21, Gi2/22 2 VLAN0002 active Gi1/1, Gi1/2, Gi1/19, Gi1/20, Gi1/23 Gi1/24, Gi1/25, Gi1/26, Gi1/27, Gi1/28 Gi1/40 3 VLAN0003 active Gi1/3, Gi1/4 4 VLAN0004 active Gi1/5, Gi1/6 检查结果：□正常 □不正常 十一、
EtherChannel检查
编号：C-B-03 检查项目：EtherChannel检查 检查命令：CISCO#show etherchannel port-channel 检查期待结果: 显示正确的etherchannel数量及每个etherchannel 包含应有的端口 备注: show etherchannel port-channel 显示本交换机中含有的portchannl的情况,具体查看每个portchannel的状态使用show int port-channel n 检查范例：（由于现实内容过多，这里只截取部分） ksy_c6509_2#show etherchannel port-channel Channel-group listing: -----------------------
11
12
Group: 1 ---------- Port-channels in the group: ---------------------- Port-channel: Po1 Ports in the Port-channel: Index Load Port EC state No of bits ------+------+------+------------------+----------- 1 55 Gi5/1 On 4 0 AA Gi5/2 On 4 检查结果：□正常 □不正常 十二、
trunk检查
编号：C-B-04 检查项目：trunk检查 检查命令：CISCO#show interface trunk 检查期待结果: trunk正常 备注:命令显示trunk信息,其中port是指参与trunk的端口,应与设计相符,mode应为on模式,status 状态为trunking, 同时对于每个trunk端口,正在trunking的vlan应与设计相符 检查范例：（由于现实内容过多，这里只截取部分） ksy_c6509_2#show interfaces trunk Port Mode Encapsulation Status Native vlan Gi2/1 on 802.1q trunking 1
12
13
Gi2/2 on 802.1q trunking 1 Gi2/3 on 802.1q trunking 1 Gi2/4 on 802.1q trunking 1 Gi2/5 on 802.1q trunking 1 Gi2/6 on 802.1q trunking 1 Gi2/7 on 802.1q trunking 1 Po1 on 802.1q trunking 1 Port Vlans allowed on trunk Gi2/1 1-4094 Gi2/2 1-4094 Gi2/3 1-4094 Gi2/4 1-4094 Gi2/5 1-4094 Gi2/6 1-4094 Gi2/7 1-4094 Po1 1-4094 Port Vlans allowed and active in management domain Gi2/1 1-15,20,100-112,120,130-132,140,150,251,253-254,430 Gi2/2 1-15,20,100-112,120,130-132,140,150,251,253-254,430 Po1 1-15,20,100-112,120,130-132,140,150,251,253-254,430 检查结果：□正常 □不正常
十三、 路由状况检查
编号：C-B-05 检查项目：路由状况检查 检查命令：CISCO#show ip route 6509_1#show ip route summary 检查期待结果:路由表应包含正确的路由信息 备注: 对于企业一般都是交换网，一条默认路由指出，只是注意VLAN信息与此直连路由是否相符。 检查范例：（由于现实内容过多，这里只截取部分） ksy_c6509_2# show ip route Codes: C - connected, S - static, R - RIP, M - mobile, B - BGP D - EIGRP, EX - EIGRP external, O - OSPF, IA - OSPF inter area N1 - OSPF NSSA external type 1, N2 - OSPF NSSA external type 2 ia - IS-IS inter area, * - candidate default, U - per-user static route
13
14
o - ODR, P - periodic downloaded static route Gateway of last resort is 192.168.254.1 to network 0.0.0.0 C 192.168.106.0/24 is directly connected, Vlan106 C 192.168.107.0/24 is directly connected, Vlan107 C 192.168.105.0/24 is directly connected, Vlan105 C 192.168.70.0/24 is directly connected, Vlan11 C 192.168.100.0/24 is directly connected, Vlan100 C 192.168.101.0/24 is directly connected, Vlan101 S* 0.0.0.0/0 [1/0] via 192.168.254.1 ksy_c6509_2# show ip route summary IP routing table name is Default-IP-Routing-Table(0) Route Source Networks Subnets Overhead Memory (bytes) connected 30 0 1920 4800 static 1 0 64 160 rip 0 0 0 0 Total 31 0 1984 4960 Removing Queue Size 0 检查结果：□正常 □不正常
十四、 生成树STP检查
编号：C-B-06 检查项目：生成树STP检查 检查命令：CISCO#show spanning-tree brief 6509_1#show span sum CISCO#show spanning-tree inte (可看具体VLAN或端口号) 检查期待结果: 跟节点,端口forwarding和blocking状态符合设计 备注: 注意根网桥的位置及优先级，最好采用命令spanning-tree vlan X root primary 设置根网桥，并相应设定备份根网桥，维护STP树的稳定。 检查范例：（由于现实内容过多，这里只截取部分） ksy_c6509_2#show spanning-tree brief MST0 Spanning tree enabled protocol mstp Root ID Priority 32768 Address 0004.dc04.1c9e Cost 20001 Port 1665 (Port-channel1)
14
15
Hello Time 2 sec Max Age 20 sec Forward Delay 15 sec Bridge ID Priority 32768 (priority 32768 sys-id-ext 0) Address 001f.9d32.b000 Hello Time 2 sec Max Age 20 sec Forward Delay 15 sec Interface Role Sts Cost Prio.Nbr Type ---------------- ---- --- --------- -------- -------------------------------- Gi1/2 Desg FWD 20000 128.2 P2p Gi1/19 Desg FWD 2000000 128.19 P2p Gi1/20 Desg FWD 200000 128.20 P2p Gi1/21 Desg FWD 20000 128.21 P2p Bound(STP) Gi1/23 Desg FWD 20000 128.23 P2p Gi1/24 Desg FWD 200000 128.24 P2p Gi1/27 Desg FWD 20000 128.27 P2p 检查结果：□正常 □不正常
十五、 接口状态检查
编号：C-B-07 检查项目：接口状态检查 检查命令：CISCO#show interface (可加具体端口号或VLAN) CISCO#show interface sum 检查期待结果: 接口运行正常,无过多的错误,广播及冲突包, 显示工作的端口为UP状态；端口冲突、错误等非信息小于1/10000。端口名称正确；端口双工状态正常。 备注: 检查范例：（由于现实内容过多，这里只截取部分） ksy_c6509_2#show interfaces GigabitEthernet2/1 is up, line protocol is up (connected) Hardware is C6k 1000Mb 802.3, address is 001e.1357.a3f4 (bia 001e.1357.a3f4) Description: connect jiulouhexin86 12#10#(1,2)-12#5#(11,12) MTU 1500 bytes, BW 1000000 Kbit, DLY 10 usec, reliability 255/255, txload 1/255, rxload 1/255 Encapsulation ARPA, loopback not set Keepalive set (10 sec) Full-duplex, 1000Mb/s, media type is LH
15
网络设备巡检报告
